The first row of the LCD display shows the currently selected driver and channel, and the joystick status On or Off. With Echo-Off, the typed commands will not be visible. What computer requirements are there to run my Picomotor from my computer? Customer Service Technical Support Information and advice about the operation of any New Focus product is available from our applications engineers. The actual state of the digital outputs 1 and 2 are controlled also by PWM command. Up to 31 distributed nodes can be controlled via the Logosol Distributed Control Network. Cnt I1 8 will cause each 8th change of digital input 9 to increment the counter by one.
|Date Added:||7 April 2008|
|File Size:||59.77 Mb|
|Operating Systems:||Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X|
|Price:||Free* [*Free Regsitration Required]|
Intelligent Picomotor Ethernet Controller
However, the host name needs to be changed to NF For intellignet, a PC can be used to monitor the motion of a device while it is being directed by a hand terminal. With the new Map command, the joystick can be set to operate any three of the 31 possible drivers in a system with one controller.
Activating Configuration Changes If any of the network parameters are changed, they must be SAVed to the non-volatile memory and the controller restarted in order picomottor the settings to come into effect.
The default mode is with all ports enabled.
C1 The user will need to go through the following steps: Can I run two axes from my Picomotor simultaneously? In order to view this screen, it is first necessary to type in the host name or Intelligebt address. If the LED is on but not flashing, an Ethernet connection has not been made. If the user presses this key again to toggle to another channel, the amplifier will be disabled, the channel changed, and then the amplifier re-enabled. Reverting Back to Factory Default Configuration If any network configuration changes cause the Ethernet connectivity of the controller to stop functioning, the user can revert back to the factory default IP configuration by flipping up DIP Switch 1 and doing a intelligent using Buttons 1, 3 and 4 on the joystick.
This Windows software application has an advanced auto-discovery feature which automatically finds computer connected Picomotor controllers and actuators. Do I have to run the Picomotor from my computer? Synchronous output command 0x05 issued to groupaddr. With these new products, the range of motion control for the Picomotor systems has been greatly expanded. This web page shows the current IP settings of the Ethernet controller.
Shortcut Keys The hand terminal features shortcut keys which allow the user to perform preprogrammed functions without the need to key in a series of MCL commands. Manual Control Using the Joystick—New Features Mapping Previous firmware revisions only allowed the joystick to operate the first three drivers. Customer Service Technical Support Information and advice about the operation of any New Focus product is available from our applications engineers.
Change the gateway address: The Echo command is now available. It has a link that can be used to retrieve the actual web page. Just plug in the included power supply and you’re ready to go.
It features a key keypad and a liquid crystal alphanumeric display that can show up to four lines of 20 characters each. To set specific speed, you will need to issue a VEL command from one of the other ports.
The first row of the LCD display shows the currently selected driver and channel, and the joystick status On or Off.
Service In the event that your product malfunctions or becomes damaged, please contact New Focus for a return authorization number and instructions on shipping the unit back for evaluation and repair. These new products are outlined in the table below.
The third and fourth lines show the response from the controller. The speed setting will affect both active channels X and Y on the joystick and will also be saved so that the user-selected range is retained during a power cycle. The corresponding model numbers are as follows: Picomotor drivers can interface with four Picomotors, but they can only move one Picomotor at a time due to power constraints.
Logosol Prealigners, Robots, CNC, Servo, Stepper, Motion Control
This warranty is in lieu of all other guarantees expressed or implied and does not cover incidental or consequential loss. Name result Type Description bool True 1 on success; false 0 on failure.
Setting the resolution equal to zero stops and clears picootor timer When no resolution value is supplied, the current value of the timer is returned. This locks access for all ports including the joystick except the port issuing the command.